地表移动带范围内建构筑物安全可靠性分析

地表建构筑物位于在生产矿山地表开采移动范围内，如果按照一般圈定地表移动范围原则判断建构筑物的安全可靠性，结果是不安全或者预留保安矿柱可保证安全。为分析地表移动带范围内建构筑物安全可靠性，采用FLAC3D软件建立数值模拟模型，对矿区地表移动进行分析研究，并结合建构筑物的破坏等级评判标准，可以更加合理地判断地表移动范围内建构筑物的安全可靠性，对存在相似条件的矿山具有一定的借鉴意义。     

化妆品功效评价(Ⅵ)——化妆品人体功效评价的实验设计

概述了化妆品人体功效评价实验设计的概念、基本要素和基本原则,介绍了常用实验设计类型和实验设计要点,提供了人体功效评价实验方案设计的思路,有助于提高研究者制定实验设计方案的水平。     

快速灵敏的LC-MS/MS法测定人血浆中阿莫西林并应用于两种制剂的一致性评价

目的: 建立快速灵敏的LC-MS/MS法测定人血浆中阿莫西林浓度，并用于两种阿莫西林胶囊的一致性评价。方法: 采用岛津公司LCMS-8060型LC-MS/MS仪，以MRM模式测定阿莫西林（m/z 366.00/114.00）的浓度，d4-阿莫西林作内标（m/z 370.10/114.05），离子源为ESI源。色谱柱选用Waters ACQUITY BEH C18（2.1×50 mm，1.7 μm），梯度洗脱。血浆样本加入内标，经甲醇沉淀蛋白后取上清液进样检测。结果: 所建方法经验证，其线性、准确度、精密度、最低定量限、提取回收率、特异性、基质效应、稳定性等各项指标均符合CFDA的指导原则及最新核查标准要求，并较文献报道中的方法有处理简单、灵敏度高、色谱峰形好的优点。结论: 所建方法快速、灵敏，适用于人血浆中阿莫西林浓度的检测。用于一致性评价的样本实测，两种制剂生物等效。     

Reliability of design approaches for axially loaded offshore piles and its consequences with respect to the North Sea

In the near future, several offshore wind farms are planned to be built in the North Sea. Therefore, jacket and tripod constructions with mainly axially loaded piles are suitable as support structures. The current design of axial bearing resistance of these piles leads to deviant results regarding the pile resistance when different design methods are adopted. Hence, a strong deviation regarding the required pile length must be addressed. The reliability of a design method can be evaluated based on a model error which describes the quality of the considered design method by comparing measured and predicted pile bearing resistances. However, only few pile load tests are reported with regard to the boundary conditions in the North Sea. This paper presents 6 large-scale axial pile load tests which were incorporated within a new model error approach for the current design methods used for the axial bearing resistance, namely API Main Text method and cone penetration test (CPT)-based design methods, such as simplified ICP-05, offshore UWA-05, Fugro-05 and NGI-05 methods. Based on these new model errors, a reliability-based study towards the safety was conducted by performing a Monte-Carlo simulation. In addition, consequences regarding the deterministic pile design in terms of quality factors were evaluated. It is shown that the current global safety factor (GSF) prescribed and the partial safety factors are only valid for the API Main Text and the offshore UWA-05 design methods; whereas for the simplified ICP-05, Fugro-05 and NGI-05 design methods, an increase in the required embedded pile length and thus in the GSF up to 2.69, 2.95 and 3.27, respectively, should be considered to satisfy the desired safety level according to DIN EN 1990 of β = 3.8. Further, quality factors for each design method on the basis of all reliability-based design results were derived. Hence, evaluation of each design method regarding the reliability of the pile capacity prediction is possible.     

抗凝冰乳化沥青涂层的性能研究

为了研究自制融雪剂对抗凝冰乳化沥青涂层性能的影响,将自制固态型融雪剂按5%、10%、15%的比例加入乳化沥青制备涂层乳液,采用水煮法、摆式摩擦仪、电导率试验分别对涂层材料的粘附性、抗滑性能和抗凝冰性能进行了测试。结果表明:自制型融雪剂对乳化沥青与集料的粘附性影响不大;随着融雪剂掺配比例的增大,抗凝冰乳化沥青涂层的摩擦系数有所降低,但均满足规范要求;相比于普通沥青涂层,抗凝冰乳化沥青涂层的抗凝冰性能得到改善,且随着融雪剂掺配比例的增大,凝冰性能逐渐提高。     

基于GA-MVFOSM法的DSA250型受电弓运动可靠性分析

为分析运动副磨损与杆件尺寸不确定性2种因素对受电弓运动可靠性的影响，提出一种基于遗传一次二阶矩法(GA-MVFOSM)的受电弓运动可靠性计算方法。首先，构建受电弓运动学方程，应用Archard磨损理论建立其运动副磨损可靠性模型。在此基础上，考虑运动副磨损与杆件尺寸的不确定性，结合可靠性理论建立受电弓运动可靠性模型。其次，利用遗传算法优化一次二阶矩法，提出GA-MVFOSM算法，用以求解受电弓的运动可靠度。最后，以DSA250型受电弓为研究对象，利用所提方法分析其运动可靠性，并与传统方法进行对比。分析结果表明:各运动副磨损量分别在0.230 0 mm、0.136 6 mm、0.006 6 mm内时，运动副磨损可靠度处于较高水平，2种因素耦合情况下弓头运动可靠度最小值为0.964 7；基于遗传一次二阶矩的计算方法可以有效提高传统方法计算精度，为提高受电弓工作可靠性提供参考依据。     

电子计价秤示值误差测量结果不确定度评定

本文介绍ACS-15电子计价秤示值误差测量结果不确定度的评定方法,并通过实际测量,计算出7.5kg秤量点的标准不确定度、合成标准不确定度及扩展不确定度。     

Seeing is believing? When scanning electron microscopy (SEM) meets clinical dentistry: The replica technique.

In restorative dentistry, the in situ replication of intra‐oral situations, is based on a non‐invasive and non‐destructive scanning electron microscopy (SEM) evaluation method. The technique is suitable for investigation restorative materials and dental hard‐ and soft‐tissues, and its interfaces. Surface characteristics, integrity of interfaces (margins), or fracture analysis (chipping, cracks, etc.) with reliable resolution and under high magnification (from ×50 to ×5,000). Overall the current study aims to share detailed and reproducible information about the replica technique. Specific goals are: (a) to describe detailed each step involved in producing a replica of an intra‐oral situation, (b) to validate an integrated workflow based on a rational sequence from visual examination, to macrophotography and SEM analysis using the replica technique; (c) to present three clinical cases documented using the technique. A compilation of three clinical situations/cases were analyzed here by means the replica technique showing a wide range of possibilities that can be reached and explored with the described technique. This guidance document will contribute to a more accurate use of the replica technique and help researchers and clinicians to understand and identify issues related to restorative procedures under high magnification.